- Valve Actuation: Solenoid
- Body Material: Aluminum
- Media: Natural Gas
- Pipe / Port Size: 3/4 “; 1 “; 1 1/4 “; 1 1/2 “; 2 “; 2 1/2 “; 3 “
- Port Type: NPTF
- Function: 2 way – 2/2 Normally Closed
- Flow: From 2.0 Cv to 6.0 Cv; From 6.0 Cv to 14.0 Cv; Over 14.0 Cv
- Voltage: 110 AC; 120 AC; 220 AC; 230 AC | 50/60
- Max Differential / Max Operating Pressure: Vacuum to 150 PSIG
- Operating Environment: Indoor, Outdoor
- Standards / Regulations: CSA, FM, Type 1, UL, Type 4
ASCO™ Series 043 Gas Shutoff Valves
- Valve Actuation: Solenoid
- Body Material: Aluminum
- Media: Natural Gas
- The ASCO Series 043 are 2-way, normally closed gas shutoff valves for on-off control of fuel gas in commercial and industrial gas burners.
- Standards / Regulations: CSA, FM, Type 1, UL, Type 4
At a glance:
- The ASCO Series 043 are 2-way, normally closed gas shutoff valves for on-off control of fuel gas in commercial and industrial gas burners.
- The valves feature a unique double-disc design with over travel that provides redundant sealing for leak-tight operation.
- The Series 043 includes visual position indication and proof of closure.
Features:
- Opening and closing response times are less than 1 second
- Visual indication of open and shut position
- Proof of closure switch rated at 1 amp
- Zero-differential piloted diaphragm
- 1/8-inch NPT upstream and downstream pipe taps with plugs for routine testing
- 5-pound closing spring for high force shut-off
You can download more at the document here: Download
Related products
Signal isolation
- The input loop-powered isolator IsoPAQ-612 provides galvanic separation for 0(4) … 20 mA standard signals, while transferring the measurement signal to the output with a high degree of accuracy.
- Input signal: 0(4)-20 mA
- Output signal: 0(4)-20 mA
- The IsoPAQ-612 requires no additional power supply since the auxiliary power is obtained from the input signal without distorting it.
Scattered light dust Measuring Devices
- The DUSTHUNTER SP100 is a type-approved measuring device with probe for very low to medium dust concentrations
- For very low to medium dust concentrations
- For small to medium duct diameters
- Emissions monitoring at power plants and waste incineration plants
- Monitoring of filter systems
- Measurements in exhaust gas or exhaust ventilation ducts
Signal isolation
- The Signal Splitter/Repeater IspPAQ-632 is used for isolation, conversion and distribution of 0/4 … 20 mA, 0/1 … 5 V and 0/2 … 10 V standard signals. The measuring input can also supply the loop power for 2-wire transmitters.
- Input signal (calibrated switchable): 0 … 20 mA, 0 … 10 V, 0 … 5 V/ 4 … 20 mA, 2 … 10 V, 1 … 5 V
- Output signal (calibrated switchable): 0 … 20 mA, 0 … 10 V, 0 … 5 V/ 4 … 20 mA, 2 … 10 V, 1 … 5 V
- The input and two isolated outputs can be easily configured by using DIP switch. Due to the calibrated range selection no further adjustment is necessary
Scattered light dust Measuring Devices
- The DUSTHUNTER SB50 is a measuring device for dust at low to medium concentrations in challenging applications, e. g., in hot or corrosive gases
- For low to medium dust concentrations
- Emission monitoring of heating installations
- Monitoring of dust concentrations downstream of filter plants
- Dust concentration measurement in cement plants
Hot-wet Extractive gas analyzers
- CEMS solutions MCS100FT
- The FTIR measuring principle allows the simultaneous determination of more than 12 measuring components – tailor-made for the particular requirements of the customer.
- Lowest approved HF measuring range: 0 ... 3 mg/m³
- Automatic spectrum adjustment via AutoVAL for reliable measuring values
- Approved according to EN 15267
- Emission monitoring in waste incineration plants
- Effective HF limit value monitoring, e. g., in aluminum production
- Monitoring of gaseous emissions in cement plants or power stations
