Ruler E accessories set SICK

VALVE CONNECTOR TYPE A Binder; Series 210 solenoid valve connectors are available with low or standard housing.; They comply with design A according to DIN EN 175301-803 (formerly DIN 43650) and have 2+PE and 3+PE contacts.; Low and high housing

Brief description: Fieldbus proxy/gateway for connecting a sensor to PROFIBUS networks; Supported products: CLV61x - CLV65x, RFH620; Cloning module support (CMC): Integrated; Supports display module (CMD): No; Supports power supply module (CMP): No; Supports fieldbus gateway (CMF): No; Serial: ✔ , RS-232; Remark: Depending on sensor connected

UNSHIELDED CABLE Binder; Unshielded; 3, 4 and 5 contacts; 3, 4, 5, 6 and 8 contacts; Cable length 100 m

Brief description: Connection of a SICK sensor in a Power-over-Ethernet (PoE) environment. Splitting of PoE signal into 24 volt supply voltage and Ethernet.; Application: Indoor; Supported products: CLV62x  CLV63x  CLV64x  CLV65x  CLV69x  Lector series RFID read/write device; Connection type: 1   x “DEVICE” connection, 15-pin D-Sub HD female connector ( ) 1   x “Ethernet” connection, 8-pin RJ45 female connector 1   x “PoE IN” connection, 8-pin RJ45 female connector 1   x “I/O” connection, 5-pin M12 female connector, A-coded; Supply voltage: 48 V DC (42 V DC ... 57 V DC); Power consumption: < 4 W, If no devices are connected and without control of the signal LEDs; Power output: 21.5 W, Without operation of signal LEDs 19.5 W, During operation of a signal LED 17.5 W, During simultaneous operation of both signal LEDs; Housing: Aluminum, polypropylene

Brief description: Small connection module for one sensor, 4 cable glands, base for CMC600; Supported products: CLV61x - CLV65x Lector62x RFH6xx RFU62x; Cloning module support (CMC): Yes; Supports display module (CMD): No; Supports power supply module (CMP): No; Supports fieldbus gateway (CMF): No; Supply voltage: (10 V DC ... 30 V DC); Power consumption: 1 W

Brief description: Connection of a SICK sensor in a Power-over-Ethernet (PoE) environment. Splitting of PoE signal into 24 volt supply voltage and Ethernet. A power supply for heating sensors can optionally be connected (e.g., for LMS511, LMS531). Suitable for use in indoor and outdoor applications with a low corrosive environment. The material of the sensor plug and the PoE connection module should be equivalent. The connection module is equipped with cable gland made of nickel-plated brass and PUR cables with nickel-plated zinc die cast M12 male connectors.; Application: Outdoor; Supported products: LMS5xx LMS1xx LMS1000 LRS4000 MRS1000 PeopleCounter picoScan100; Scope of delivery: PoE connection unit, 2 x M4 x 16 mm hexagon screws for mounting the unit, 1 x RJ45 adapter; Connection type: 1   x “Ethernet” connection, 8-pin RJ45 female connector 1   x “Supply voltage to sensor” connection, 5-pin M12 female connector, A-coded 1   x “Ethernet sensor” connection, 5-pin M12 female connector, A-coded; Supply voltage: (42.5 V DC ... 57 V DC), according to PoE, IEEE802.3at Type 2, Class4 / PoE+; Power output: Max. 25 W; Housing: Aluminum, polypropylene

Brief description: Connection device basic for connecting one sensor with 2 A fuse, 5 cable glands and RS-232 interface to sensor via M12, 17-pin female connector, all outputs available on screw/spring-loaded terminals.; Supported products: Lector series CLV62x - CLV64x (depending on type) CLV69x RFID read/write device InspectorP series; Cloning module support (CMC): Yes; Supports display module (CMD): No; Supports power supply module (CMP): No; Supports fieldbus gateway (CMF): No; Supply voltage: (10 V DC ... 30 V DC); Power consumption: 1 W

SHIELDED CABLE Binder Shielded; 3, 4 and 5 contacts; 3, 4, 5, 6 and 8 contacts; Cable length 100 m